Welcome to Blue-Kote

GENERAL DESCRIPTION:

BLUE-KOTE will cure to a tough protective plastic film, which can be easily peeled off by hand when no longer required. BLUE-KOTE is a water based liquid coating that can be applied by airless spray, conventional air spray (may require thinning with water), or by brush or roller. Clean up BLUE-KOTE as you would with other water based paints. Clean up with water.

Primary used to protect fibreglass parts and moulds. Protects boat decks, hulls, hull liners, tubs, showers, plastic parts and most non-porous surfaces from paint, plaster, sealants, resins, polyurethane foam and abrasives during construction, storage, assembly, transportation and repair. BLUE-KOTE has been used to protect the following surfaces: Gel coat, Acrylic, Polycarbonate, Glass, Aluminum and Stainless Steel. BLUE-KOTE is not recommended for coating raw mild steel

PRODUCT CHARACTERISTICS

APPEARANCE

Light blue viscous liquid when wet, translucent blue film when cured

COVERAGE

(Sq. Ft/mil of dry film/gal.) 540, Weight (pounds per gallon) 9.0, Storage Life (In closed container) 6 Mo. @ 80degrees F, Minimum film forming temperature 50degrees F. Recommended dry film thickness-6 to 8 mils, weight 10lb

PRODUCT PACKAGING

Products are furnished in carton of 4-1 gallon pails, in 5-gallon plastic pails, and 55-gallon drums. 330 gallon disposable containers also available

PRODUCT APPLICATION

AIRLESS SPRAY APPLCATION:

NOTE: this product has been formulated to provide optimum coat coverage without running or sagging on vertical surfaces with airless spray equipment.

Airless spray equipment capable of generating a fluid pressure of 2000-2500 pounds. Select the tip size suitable for your application and equipment capabilities. Adjust the fluid pressure to achieve proper atomization and spray pattern

BRUSH AND ROLLER APPLICATION

Brush or poll on as heavy a coat as possible moving in one direction and allow to dry. A Second coat may be required. Apply the second coat perpendicular to the first to obtain a strong, uniform film.

PRODUCT PRECAUTIONS

• DO NOT allow product to freeze. Frozen product cannot be rejuvenated and will not function properly.
• DO NOT apply to surfaces other than those specifically noted prior to thoroughly testing.
• DO NOT apply the coating too thin. This will result in a weak discontinuous film, which will be difficult to remove and offer no protection.
• DO NOT apply this product in the rain, moisture or freezing temperatures before it can fully cure.
• WARNING! CONTAINS MODIFIED ACRYLIC LATEX AND AMMONIA. DO NOT ALLOW TO FREEZE! KEEP OUT OF THE REACH OF CHILDREN. DO NOT TAKE INTERNALLY.

BK-1: Blue-Kote single gallon
BK-2: Blue-Kote two gallon
BK-5: Blue-Kote 5 gallon case

INQUIRE FOR CURRENT PRICING AND AVAILABILITY

Blue-Kote R-18 is a water based, air or forced dry, hand peel-able, U.V. resistant, temporary protective coating. When applied to most non-porous surfaces (glass, porcelain, fiberglass, gel coat, aluminum and stainless steel) the coating provides protection from abuse. Do not use R-18 on acrylic due to high adhesion.

R-18 minimizes surface damage during assembly, rigging, shipment, installation, and subsequent construction or rehab work. Paint, sealants, abrasives and chemicals are kept away from protective surface. Just prior to final inspection, the coating is easily peeled from the surface. In addition to forming an extremely tough film R-18 exhibits  quick dry times and good water resistance when fully cured.

PRODUCT CHARACTERISTICS

APPEARANCE

Blue-Kote paint is a viscous light blue liquid.

COVERAGE

(SQ. FT/MIL OF DRY FILM/GALLON): 786, POUNDS PER GALLON: 8.9 + 0.2., COATING V.O.C., (EPA Method 24): 0 G/L or 0.0 Lb/Gallon.

STORAGE LIFE (IN CLOSED CONTAINER):

6 Mo. at recommended temps.

MINIMUM FILM FORMING TEMPERATURE:

50 degrees F.

PRODUCT PACKAGING

R-18 is supplied ready to use for roll-on, brush,air or airless spray application in 1 gallon pails (4 per case), 5 gallon pails, or 55 gallon drums.

STORAGE

Store at temperatures above 50 degrees F. and below 110 degrees F.

RECOMMENDED DRY THICKNESS

4 to 8 mils.

CURE CYCLE

Air cure time will vary depending on wet film thickness and atmospheric conditions (temperature, air velocity, and relative humidity). Optimizing these conditions will decrease dry times. Consult your product representative for further information

PRODUCT USE INSTRUCTIONS

GENERAL:

The following directions and recommendations are intended to serve as a guide and may require modification to meet local conditions. No Mixing required. Use as received. Do not thin. The intended substrate must be clean and dry to accept the protective coating properly. Loose debris, or dust, or other contamination may degrade product effectiveness and peel-ability.

AIRLESS SPRAY APPLICATION

Airless spray equipment capable of generating a fluid pressure of 2000-2500#. Select a tip size suitable for your application and equipment capabilities. Adjust the fluid pressure to achieve proper atomization and spray pattern.

CONVENTIONAL AIR SPRAY APPLICATIONS

Conventional air spray equipment may be used. Some products may require the use of a larger fluid nozzle and/or thinning with water to spray. Note that the addition of water will require you to apply more material to obtain the desired dry film thickness and will increase the time to dry the coating. Use as little water as possible.

ROLLER AND BRUSH APPLICATION

Roll or brush on as heavy a coat as possible in one direction and allow drying. A second coat may be required. Apply the second coat perpendicular to the first to obtain a strong, uniform film. Dry film build required in mil. 4 : 5 : 6 : 7 : 8 : 9 : 10 : 12. Wet mils. to apply  9 : 11 : 13 : 14 : 16 : 18 : 21 : 25. **Square feet of coverage 194 : 155 : 129 : 111 : 97 : 86 : 75 : 64. ** Theoretical Coverage-Actual coverage may be slightly lower due to transfer efficiency factors. Seller makes no warranty of any kind, express or implied, as to the merchantability, fitness for any particular purpose, or any other matter with respect to this product. Since conditions of use are beyond sellers’ control, buyer assumes all risk of use of this product. Sellers’ sole obligation will be to replace the product if found to be defective. It is the user’s responsibility to determine the suitability for use of this product under the conditions present at the time of application. M.S.D.S. available upon request.

PRODUCT PRECAUTIONS

NOTE: CONSULT MATERIAL SAFETY DATA SHEET FOR HANDLING AND SAFETY

Use with adequate ventilation.

DO NOT TAKE INTERNALLY. Avoid prolonged contact with skin. While spraying, wear a suitable respirator with an ammonia cartridge to prevent inhalation of over spray and vapors.

Keep containers closed when not in use.

DO NOT allow the product to freeze. Frozen liquid material cannot be rejuvenated  and will not function properly.

DO NOT apply the product to other surfaces other than those specifically noted prior to thoroughly testing.

DO NOT apply the coating too thin! This will result in a weak discontinuous film,which will be difficult to remove and offer no protection.

DO NOT apply the coating when it will be exposed to rain, moisture or freezing temperatures before it can fully cure.

DO NOT attempt to peel the coatings at extreme temperatures. They will peel easily at normal room temperature. Very high temperatures (more than 160 deg. F.) may cause the coating to fail.

DO NOT apply the coating over small, intricate or delicate parts. These areas should be masked with plastic film or tape as the coating may be difficult to remove.

WARNING! CONTAINS MODIFIED ACRYLIC LATEX. DO NOT ALLOW PRODUCT

Blue-Kote Tape is a highly visible, tough, pressure sensitive 7 mil. blue vinyl threshold tape. It can be used for abrasion protection, duct sealing, joint sealing, decorating, packaging, aisle marking and threshold protection.Temporary product used to protect smooth, nonporous surfaces. Used for taping and masking under Blue-Kote temporary scratch protector. For protecting fiberglass and gel coat, door jambs, edges of dive platforms, stairs, etc.

Use on countertops, aluminum, vinyl and bathroom fixtures.

BKT-547: Blue-Kote Tape 1/2″ x 36 yds(108′)
BKT-552: Blue-Kote Tape 1″ x 36 yds(108′)
BKT-557: Blue-Kote Tape 2″ x 36 yds(108′)
BKT-562: Blue-Kote Tape 3″ x 36 yds(108′)
BKT-567: Blue-Kote Tape 4″ x 36 yds(108′)
BKT-572: Blue-Kote Tape 6″ x 36 yds(108′)
BKT-577: Blue-Kote Tape 8″ x 36 yds(108′)

GENERAL DESCRIPTION:

Blue-Kote Carpet Mask is temporary carpet protection, Carpet mask uses a SOLVENT-BASED adhesive for easy unroll and apply to carpet. Resists puncturing, stays in place, easy removal, skid resistant & does not transfer adhesive to carpet.

Many companies are selling carpet protection these days, all claiming their film is the best. The fact is Carpet Mask out performs all these products. Solvent-based adhesive offers several significant advantages and protection from potential carpet damage to the user.

PRODUCT CHARACTERISTICS

• Film is easy to unroll and apply to the carpet, saving you labor dollars.
• Solvent-based adhesives coat the film more evenly in the manufacturing process. This allows the film to adhere to the carpet evenly rather than having pockets of non-sticking film or “float” as is often the case with water-based products.
• Film will not break down with conditions of moisture as water-based films do.

So the next time you plan on purchasing a self-adhesive film to protect valuable carpeting, for the best protection for you and your carpet, think Carpet Mask.

CM-24S: Carpet-Mask Film 24” x 200’ (single)
CM-24:

Temporary floor protection.

Cost effective and safe for all surfaces, perfect for protecting concrete and epoxy floors, green (made from 100% recycled products and can be recycled).

Construction Board does not stain and can be reused, is durable enough for any job site, durable enough to drive a forklift over it and has earned USBGBC Certified Leed’s Points: material and resource credit 2.1 or 2.2

Rolls measure 38″ x 100′ (96.5cm x 30.5cm)

316 Square Feet (29.4 SqM)

Blue-Kote Engline Cowl film is a pressure sensitive rubber adhesive coated UV stabilized polyolefin masking film. Engine cowl film is designed for the protection of engine cowl finishes during rigging, service and under shrink wrap covers during transportation to prevent chafing and scratching to the painted surfaces. This film can be left on for 30-45 days without transfer of adhesive to the substrate

Cowl film is also used to protect acrylic surfaces from scratching and scuffs.

MCF-24S: Engine Cowl anti Scratch/Chafe film 24” x 200’ (SINGLE ROLL)
MCF-24: Engine Cowl anti Scratch/Chafe film 24” x 200’
MCF-48:  Engine Cowl anti Scratch/Chafe film 48” x 200’
MCF-48s: Engine Cowl anti Scratch/Chafe film 48” x 200’ (SINGLE ROLL)

GENERAL DESCRIPTION:

Blue-Kote Floor Mask is for use on hardwood and polished floors. The product is durable, reusable and simple to use. A Non-Adhesive, 100% non-woven runner has non-skid backing which stays put in short lengths. Blue-Kote Floor Mask is the perfect floor protection that also gives you a highly absorbent and easy to use surface cover.

FM-24NT: Floor-Mask non tack reusable 36” x 50’
FM-24s: Floor-Mask Film 24” x 200’ (single)

Blue-Kote Heat Shrink Tape Contains No UV Inhibitors. Could leave an adhesive residue if applied directly to paint, fiberglass, etc. Use to tape vents and doors onto cover–and to repair holes in the shrinkwrap. A polyethylene film tape for convention center floor marking, seaming and splicing of polyethylene sheeting and general purpose holding. Tape features a low residue adhesive.

PRODUCT CHARACTERISTICS

• Heat Skrink Tape specs: Total Thickness: 9 mils
• Adhesion to Stainless Steel: 70 ounces per inch
• Tensile Strength: 22 pounds per inch

HST60s15: Heat Shrink Tape (white) 1.5″ x 60yds(108′) single roll
HST60s: Heat Shrink Tape (white) 3″ x 60yds(108′) single roll
HST60b:Heat Shrink Tape (white) 3″ x 60yds(108′), 4 case lots, bulk price min. order of 4 cases
HST60: Heat Shrink Tape (white) 3″ x 60yds(108′), 16roll/case
HST6015: Heat Shrink Tape (white) 1.5″ x 60yds(108′), 32 roll/case

Sling Shield Tape:
Sling-Shield tape is used to secure Sling-Shield to desired height on lift
slings. Resistant to aging, sun, water, fungus, oil, acids, alkalis and
corrosive chemicals.
SST-553: 1.5″ X 36 yd. (108′) white or red $5.35 per roll.
SST-553case: Case of 32 rolls – $131.00
SST-60: 1.5″ X 60 yd. (108′) white or red $6.75 per roll.
SST-60case: Case of 32 rolls – $200.00

Poly-Craft mask joining tape:
Poly vinyl tape is used as a seam tape for Poly-Craft Mask. Also used to
secure mask to substrate (fiberglass, tile, marble and stainless steel. Will
not leave adhesive residue when removed. White other colors available special
order, 6 days

SST-557: 2″ X 36 yd. $6.05 per roll
SST-557case: 24 rolls per case $131.00 per case
SST-562: 3″ X 36 yd. $9.05 per roll
SST-562case: 16 rolls per case $131.00 per case

Poly-Craft Mask (R) consists of a three-ply protection system: a fiber glass mesh between a 40-point craft paper and a polyethylene sheet.

Water proof and tear resistant. Perfect for hardwood floors, tile, vinyl, marble, any surface where you used to use rosin paper. Quickly becomes a must-have product for quick on the job protection. 100 times stronger than rosin paper.

36″x200′ roll, 600 Square Feet
$78.60 1 to 3 rolls
$68.50 4 rolls & up per roll

NEW!

PCM6-300 72″ x 300′ (1800 sq. ft.) wt 47 lb.
$255.00

Poly-Craft mask joining tape:
Poly vinyl tape is used as a seam tape for Poly-Craft Mask. Also used to
secure mask to substrate (fiberglass, tile, marble and stainless steel.

Click here to View and Purchase Tape

Blue-Kote Preservation Tape Contain UV inhibitors for long term storage. Product will not leave adhesive residue if applied directly to fiberglass, paint, graphics, etc.

Hull preservation tape and is used for taping edges of shrink wrap to a boat’s hull. It has a polyethylene film and rubber based adhesive. UV protected for prolonged expose to sunlight. Preservation tape features residue free removal from most surfaces. Preservation Tape is used to seam shrink wrap film sheeting together, patch holes in the shrink wrap, secure the wrap, and to hold doors in place. Tape comes with serrated edges for easy tearing with no cutting needed.

PRODUCT CHARACTERISTICS

• Total Thickness: 7 mils
• Adhesion to Stainless Steel: 40 ounces per inch
• Tensile Strength: 22 pounds per inch

PST-36s: Preservation Tape 3″ x 36 yds(108’), SINGLE ROLL
PST-36: Preservation Tape 3″ x 36 yds(108’), 16 roll/case

GENERAL DESCRIPTION:

Rapid-Shrink KP118-H features 500,000 BTU’s of shrink wrap power extension shrink tool. Shrink faster with Rapid-Shrink KP118-H long reach heat tool for high and wide objects. “As fast as you can walk the length of a boat the Rapid-Shrink heat tool can shrink the film.”

Regular MSRP price $325.00.  Euroglass Protective Products price now available for only $276.60

PRODUCT CHARACTERISTICS:

• 500,000 BTU’s of shrink wrap power
• 18″ bent brass extension
• 25′ hose
• Regulator & spark ignitor.
• Extensions available

EX8: EX-8 bass extension 4”
EX30: EX-8 bass extension 30”
EX40: EX-8 bass extension 40”
BP-66: BP-66 Torch Tip 300k with built in piazo igniter
KP118H: Rapid-Shrink KP118-H heating tool, includes 18″ extension, 25′ hose, regulator and ignitor

GENERAL DESCRIPTION:

Ripak 2200 heating tool 145,000 BTU of shrink wrap power is a “Cold Nozzle” shrink wrap tool. It comes with a 25′ of hose, adjustable auto-shut off safety regulator (if gas flow is interrupted regulator will shut off down ensuring safety first) and comes in a high quality padded poly carry case.

Regular MSRP price $926.99.00. Euroglass Protective Products price now available for only $718.00.

24″, 48 7 72″ Extensions are available, call or e-mail for extension pricing.

PRODUCT CHARACTERISTICS:

• Almost instant electronic-Piazo ignition,
• Well balanced aluminum body for durability
• Comfortable grip for extended use
• Defuser grill installed in nozzle
• Eliminates flame flash backs into tool body that causes irreparable damage to other heat tools
• Patented “Cold Nozzle” banishes contact burns to skin and burn holes in shrink film caused by nozzle contact to film during confines

Ripak is the tool of choice since 1981 by the internationally renouned shrink wrap company; Euroglass Mobile Shrink Wrap Service. http://www.mobileshrinkwrap.com

Ripak Heat gun 2 piece Combo Modular extensions NOW AVAILABLE.
They are adjustable so you get 2 extensions for the price of one.

RP2200: Ripak 2200 145,000 BTU heating tool
RPC4-6: Ripak Combo 4-6 extension 4.9feet(1.45m)
RPC6-4: Ripak Combo 6-8 extension 6.8feet(2.03m)

GENERAL DESCRIPTION:

Blue-Kote Professional Shoe and Boot Covers offers you the opportunity to take customer satisfaction to a new level and enhance your professional image with these high quality, vinyl or non-woven cloth non-skid shoe and boot covers.

PRODUCT CHARACTERISTICS

• Universal size
• Keep decks and cockpits clean during assembly and service
• Keep carpets clean
• Marina boat showroom: customer boarding new boats
• Boat shows: customer boardings
• Final walk through on new home construction
• Showing custom homes, home inspections and real estate-open house

BCV-25: Vinyl Shoe Cover-25 Pairs/Box
BCC-25: Cloth Shoe Cover-25 Pairs/Box
BCV-50: Vinyl Shoe Cover-50 Pairs/Box
BCC-50:Cloth Shoe Cover-50 Pairs/Box
BCv-100: Vinyl Shoe Cover-100 Pairs/Box
BCC-100: Cloth Shoe Cover-100 Pairs/Box

Shrink film knives are designed to cut film, shrink over wrap, string and twine. Quick easy blade changing.
SafeTcut snaps open with twist of a screwdriver for quick blade changing. Snaps shut. Blades are reversible. Use standard “Schick” injector blade.

T100BL: Replacement blades for the T100 Film Knife. Includes 10 razor blades. (bulk)
T100HD: Shrink film knives are designed to cut film, shrink over wrap, string and twine.

100% virgin resin, true mil thickness’, maximum UV inhibitors designed to help save you time and money.  Our Shrink Wrap offers UVI protection and strength. UVI is used for the protection from film deterioration and in combination with “Ethyl Vinyl Acetate” it contributes to the elasticity and puncture resistance of shrink wrap.

Our shrink wrap provides a tight  smooth form fitting, heat sealed surface secured around your boat which  will prevent water from pooling and protect your boats gel-coat finish  from chafing that occurs from boats covered by tarps and canvas. It’s no secret that boats left exposed to harsh weather like Florida’s sun and rain will eventually  deteriorate. Vandals, Birds, Insects and Rodents, Rain, Sun and Wind, Condensation, Mold, Mildew  and Rust are stopped when your boat is shrink wrapped.Euroglass shrink  wrapping keeps your boat in exactly the same condition as the day it was  wrapped.With Almost 30 years in Shrink Wrap (since 1981) our Parent company Euroglass knows Shrink Wrap. There can be no dirtier and more dangerous place in the world, than among the busy cities and highways of America. Shrink wrap stops all these damaging problems before they can begin. A wind resistant, impenetrable form fitting, heat sealed surface, shrink wrap keeps your boat as clean as the day it was wrapped. Shrink  wrap also provides security, keeping people off your boat whenever it stops along the way during transportation.

WARNING: Shrink wrap can  burn. If heat is applied incorrectly, shrink wrap can ignite into open flame. It  can also drop down onto other combustible material and cause secondary ignition  and fire. If at any time you observe the shrink wrap on fire, immediately stop  what you are doing and carefully inspect the area where you are working for  possible fire. Keep a fire extinguisher available at all times. Tape/seal off  fuel vents prior to covering! This is VERY important to prevent  explosions; call the boat builder if vents cannot be found, some fuel vents  are incorporated into the fuel  cap.

Options are formatted by size and then thickness. This means that 17’x110′ shrinkwrap 7-mil will be listed as “17×110-7m“.

Polyethylene boat lift protective sling sleeve

6 mil white 16″ X 600′ and 18″ X 600′ rolls. Similar to shrink wrap material. Manufactured specifically for the protection of boat lift slings and boat hulls during launch and haul-out. Sling-Shield rinses clean, keeping dirt off lift slings. Simple 1 man installation.

16″ for standard boat lift slings.

18″ for slings with rub-rail pads.

You will need a Dispenser to use this product. They come in both 16′ and 18′ sizes.

SS166066: 8″ X 600′ roll, white, 6mil, 20lb.
SS166066: 16″ X 300′ roll, white, 6mil, 23lb.
SS186066: 16″ X 600′ roll, white, 6mil, 53.6lb.
SS166066: 18″ X 300′ roll, white, 6mil, 25.5lb.
SS186066: 18″ X 600′ roll, white, 6mil, 58.5lb.
SS366008: 36″ x 600′ roll, white, 8mil

Dispensers:
SSHD16: 16″ Holder
SSHD18: 18″ Holder

Sling Shield Tape:
Sling-Shield tape is used to secure Sling-Shield to desired height on lift
slings. Resistant to aging, sun, water, fungus, oil, acids, alkalis and
corrosive chemicals.
Click here to View and Purchase Tape

GENERAL DESCRIPTION:

Blue-Kote woven polyester banding cord strapping & wire coated anti-slip buckles; 3/4″ woven polyester cord strapping 1050# breaking strength.

BKSB-1: Strapping/Buckles 2100’ x 3/4″ roll (single)
BKSB-4: Strapping/Buckles 2100’ x 3/4″ roll (case of 4)
BKSB-D: 3/4″ coated non-slip buckle 100count

A complete line of deck underlayment products and systems utilized in the construction, overhaul and repair of decking and other surfaces in the marine environment. Products are certified for US Navy use, including ultra lightweight underlayments that meet Navy military specifications for weight and performance.

High quality epoxy color and clear topcoats are utilized to provide a decorative, scratch-resistant, long lasting deck and surface covering. Products are US Coast Guard (USCG) approved with Wheelmark accreditation

NOTE: Ultra light Terrazzo 1290 (1 gallon kit) is a 3 part system. Part A is resin in 1 gallon can. Part B is hardener or catalyst in a quart can. Part C is dry bead in 2 bags, one neutral and the second colored bead. The total volume mixed is 3.25 gallons. Minimum order 2 kits. Boxed 2 kits per case.

1222-R: Bond Coat (part A&B) 200-250 sq. ft.
1231-R: Combo Tile Grout (colour options available)
1255B-R: Underlayment Sealer (sealer kit, high viscosity) 100-125 sq. ft.
1290-R: Ultra Light Underlayment ((kit), aggregate, resin, hardener)
1290B-R: Ultra Light Underlayment in bucket (Kit 1290 in bucket) 18-20 sq, ft,
1290T-R: Ultra Light Terrazzo 1 gal. kit, Part A & Part B, 18-20 sq. ft.
2102-R: Water proofing membrane membrane (grey) 150-250 sq. ft.
5000-R: Clear Epoxy Top Coat 100% Solids, zero VCO, Epoxy 120-140 sq. ft.
50XX-R: Color Epoxy Coat 100% Solids, Zero VOC, Epoxy 120-140 sq. ft.
5100-R: Clear Epoxy Top Coat IMO 100% Solids, Zero VOC, Epoxy 120-140 sq. ft.
51XX-R: Clear Epoxy Coat IMO 100% Solids, Zero VOC, Epoxy 120-140 sq. ft.
5501-R:  Epoxy Adhesive HALF gal. kit, Epoxy Adhesive 18-20 sq. ft.
FR0499: Underlayment mix – in bucket (Bag, sand mix in bucket) 18-20 sq. ft.

Polyester cord strap tension tool is used when installing shrink wrap strapping to better secure the shrink wrap cover to your project by tightening banding.

Blue-Kote Anti-chafe film is a maximum adhesion that is easy peel off with NO adhesive residue or transfer. Travel-Tak also provides UV protection. Used to protect gel coat, painted hulls and graphics, from rub and chafe marks as well as dirt and grime.

This film is two sheets of high quality PE welded together to make an extremely durable plastic that can withstand high winds and UV exposure. The adhesive is a natural rubber base which allows maximum adhering strength and easy peel off with no adhesive transferring

*200′ rolls can be cut to desired widths saving inventory of multiple sizes, less waste

TK-6s: Travel-Tak anti-chafe film 6″ x 200’ (single)
TK-12s: Travel-Tak anti-chafe film 12″ x 200’ (single)
TK-24s: Travel-Tak anti-chafe film 24″ x 200’ (single)
TK-48s: Travel-Tak anti-chafe film 48″ x 200’ (single)
TK-6: Travel-Tak anti-chafe film 6″ x 200’, 4 roll case
TK-12: Travel-Tak anti-chafe film 12″ x 200’, 4 roll case
TK-12b: Travel-Tak anti-chafe film 12″ x 200’, 8 per case, bulk rate, min. order of 8
TK-48: Travel-Tak anti-chafe film 48″ x 200’, 4 roll case

Steiner shrink-wrap welding high performance, professional cushion core, split cowhide gloves. Are used during shrink wrapping to protect against burns. A favorite glove among professional shrink wrappers and welders.

PRODUCT FEATURES

Cushioned glove core lining keeps hand cool longer during shrink film pleat and seam welding
Natural wing thumb for comfort and maneuverability
Tight fit to hand
Spark-resisting welt stitching
Stitched with flame-resisting Kevlar thread

2519B: 1 left hand & 1 right hand glove
2519BLH: 2 left hand gloves
2519BRH: 2 right hand gloves

GENERAL DESCRIPTION:

Blue-Kote Window Mask is a translucent blue film used as protection for windows during painting, spray gel coat etc. 2mil polyethylene film coated with low-tack adhesive. Window Mask is a strong, linear low density, 2 mil. polyethylene film coated with a solvent-based, low-tack adhesive. This special formula allows Window Mask to also adhere to substrates such as plastics, finished metal and aluminum without any damaging effects upon removal.

Window-Mask Film 24” x 600’ (single)